Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3
- Product Code
- 643693
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Tin sulphate | 7488-55-3 | 10 - 30% | Yes |
| 4-Sulphophthalic acid | 89-08-7 | 1 - 5% | Yes |
| Sulfuric acid | 7664-93-9 | 1 - 5% | Yes |
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist.
Remove contaminated clothing and footwear. Flush with large amounts of water. Seek immediate medical attention.
Rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention.
DO NOT induce vomiting unless directed to do so by medical personnel. Give one to two glasses of water or milk. Never give anything by mouth to a victim who is unconscious or is having convulsions.
Immediate Medical Attention
Seek immediate medical attention for skin and eye contact.
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
carbon dioxide, foam, powder, water spray jet, fine water spray
Not available.
Not available.
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so.
Absorb spill with inert material. Shovel material into appropriate container for disposal.
Materials: inert material
Related Products
Similar products with comparable safety profiles
BONDERITE M-ED 9000A ANODIZING ADDITIVE
---
BONDERITE M-ED EA1022 ANODIZING ADDITIVE
---
BONDERITE M-ED ALUMINUX LL ANODIZING
---
BONDERITE M-ED 9000L ANODIZING ADDITIVE known as COLORMAX 9000L
---
BONDERITE M-ED ST-2 known as COLORMAX ST-2 ENHANCER
---
BONDERITE M-ED SEAL NF-1 ANODIZING SEAL known as ALMECO SEAL NF-1 ADDITIVE
---
BONDERITE M-ED SEAL MT ADDITIVE
---
BONDERITE M-CR 1201 CHROMATE COATING known as ALODINE 1201 MTO
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not breathe gas/fumes/vapor/spray. Wash thoroughly after handling. For industrial use only. Avoid contact with eyes, skin and clothing. Use caution when combining with water; DO NOT add water to acid, ALWAYS add acid to water while stirring to prevent release of heat, steam and fumes.
Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Manufacturer recommends storing above 4.4 °C (40 °F). Thaw and mix thoroughly if frozen.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
Will not occur.
Store away from incompatible materials.
Adding water to this product may cause localized overheating and splattering. Keep away from organic materials, combustible materials, alkalis and metals.
Irritating and/or toxic fumes and gases may be emitted upon the product's decomposition.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 2586
- Shipping Name
- Aryl sulfonic acids, liquid
- Transport Class
- 8
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3?
The signal word is danger.
What is the physical form of BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3?
BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3 is a liquid with colourless / colorless color. It has odourless / odorless odor.
What is the solubility of BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3?
fully soluble Water
What are the hazard statements for BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3?
This substance has 3 hazard statements:
- H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H350: MAY CAUSE CANCER.
What is the melting point of BONDERITE M-ED ST-3 ANODIZING ADDITIVE known as ALMECOLOR ST-3?
The melting point is Not available. and the boiling point is 212 °F (100°C) None.