Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- DERTOLINE® R
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
adhesives, bitumen modification
Manufacturers & Suppliers
LES DERIVES RESINIQUES ET TERPENIQUES (DRT)
manufacturer
30 rue Gambetta, BP 90206, F-40105 DAX CEDEX, FRANCE
33-(0)5 58 56 62 00
Emergency Contacts
NCEC
+44 1235 239670
24/24 – 7/7
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of resins
For the wording of the listed hazard phrases refer to section 16. Statut REACH REACH registration number of substance with CAS 8050-26-8 : 01-2119486685-21-xxxx REACH registration number of substance with CAS 8050-31-5 : 01-2119488167-27-xxxx
Notes
Hazardous components: Not applicable.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air. If symptoms are experienced, get medical attention. In case of unconsciousness place patient stably in side position for transportation.
Product at ambient temperature: Immediately rinse with plenty of water. Remove contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention if irritations occurs. Hot product: Immediately immerse or flush the burn area with large amounts of cold water (at least 15 minutes). Do not remove solidified material from burned skin as the damaged skin can be easily torn. Transfer immediately to hospital.
Product at ambient temperature: Immediately rinse with water. Remove contact lenses if present and easy to do. Hold eyelids apart and flush eyes with plenty of cool low-pressure water for several minutes. If symptoms persist, consult a doctor. Hot product: Do not open eyelids if covered with resins. Immediately flush eyes with large amounts of water for at least 15 minutes. Do not remove solidified material from burned eye as the damaged tissues can be easily torn. Transfer immediately to hospital.
Do not induce vomiting. If the person is conscious, immediately rinse out mouth with water. No adverse health effects are expected from accidental ingestion of small amounts of this product. In case of lasting symptoms, consult a doctor. For ingestion of large amounts: do not induce vomiting and get medical attention.
Immediate Medical Attention
Get medical attention if irritation occurs. Transfer immediately to hospital for hot product exposure. Get medical attention for ingestion of large amounts.
Medical Treatment
For doctors: Mineral oil may be used to loosen and soften the material.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO₂, powder or water spray. Fight larger fires with water spray or foam.
In case of fire, may release irritant and toxic fumes.
Firefighter Protection
Firefighters should wear appropriate protective equipment and self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unprotected persons away.
Do not allow product to reach soil, waterways, drains and sewers.
Pick up mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wear appropriate personal protective equipment. Provide adequate ventilation in the workplace. Avoid as much as you can the formation of dust.
Store if possible under cover in a cool well-ventilated location.
Protect against electrostatic charges. Use only non-sparking tools. Protect from heat. Keep ignition sources away.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide local exhaust or general room ventilation to minimize exposure to dust.
Protective gloves resistant to chemicals (standard EN 374-1). They should be replaced regularly and if there is any indication of degradation or chemical breakthrough.
Safety glasses (standard EN 166)
In case of insufficient ventilation: Avoid breathing particles by wearing a dust mask (FFP3 or FFP2 as a minimum). Avoid breathing vapors by wearing an appropriate filter cartridge mask.
Protective work clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under normal storage and handling conditions.
No data from specific reactivity tests are available for this product.
Dust may ignite on contact with electrostatic discharge or exposure to flame or other sources of ignition
Avoid dust formation when handling the product.
No incompatible materials known.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for DERTOLINE® R?
The signal word is no signal word.
What is the physical form of DERTOLINE® R?
DERTOLINE® R is a solid with dark yellow color. It has light odor.
What is DERTOLINE® R used for?
adhesives, bitumen modification
What is the melting point of DERTOLINE® R?
The melting point is ≥90,0 °C (Ring & Ball) and the boiling point is Not determined.