Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- terralin® protect
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Disinfectants and general biocidal products
Uses advised against
For professional users only.
Manufacturers & Suppliers
Schülke & Mayr GmbH
manufacturer
Robert-Koch-Str. 2, 22851 Norderstedt, Germany
+4940521000
http://www.schuelke.com
Emergency Contacts
UK Poisons Emergency number
0870 600 6266
Emergency Contact
+49 (0)40 / 52 100 –0
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Quaternary ammonium compounds, benzyl-C12-16-alkyldimethyl, chlorides EC: 270-325-2 | 68424-85-1 | 22% | Yes |
| 2-Phenoxyethanol EC: 204-589-7 | 122-99-6 | 10 - 20% | Yes |
| Tridecylpolyethylenglycolether | 69011-36-5 | 5 - 15% | Yes |
| Propan-2-ol EC: 200-661-7 | 67-63-0 | 3 - 8% | Yes |
| Alkyl polyglycol ether | 31726-34-8 | 5% | Yes |
| Tetrahydroxypropylethylendiamin | 102-60-3 | 5% | Yes |
| Amines, n-C10-16-alkyltrimethylenedi-, reaction products with chloroacetic acid | 139734-65-9 | 0.9% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move the victim to fresh air and keep him calm. If unconscious place in recovery position and seek medical advice. If symptoms persist, call a physician.
Wash off immediately with plenty of water for at least 15 minutes. If symptoms persist, call a physician.
In case of eye contact, remove contact lens and rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Obtain medical attention.
Do NOT induce vomiting. Rinse mouth with water. Give small amounts of water to drink. Obtain medical attention.
Immediate Medical Attention
Obtain medical attention.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Dry powder, Foam, Carbon dioxide (CO2), Water spray jet
High volume water jet
Do not allow run-off from fire fighting to enter drains or water courses.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Increased risk of slipping in the presence of leaked / spilled product.
Do not flush into surface water or sanitary sewer system. Avoid subsoil penetration.
Wipe up with absorbent material (e.g. cloth, fleece). Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust).
Materials: cloth, fleece, sand, silica gel, acid binder, universal binder, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Prepare the working solution as given on the label(s) and/or the user instructions. Avoid exceeding of the given occupational exposure limits (see section 8). Wear personal protective equipment. Avoid formation of aerosol.
Store at room temperature in the original container. Keep away from heat. Keep away from direct sunlight. Keep container tightly closed.
Keep away from food and drink.
No special protective measures against fire required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure that eyewash stations and safety showers are close to the workstation location.
Splash protection: disposable nitrile rubber gloves e.g. Dermatril (layer thickness: 0,11 mm) made by KCL or gloves from other manufacturers offering the same protection. Prolonged contact: Nitrile rubber gloves e.g. Camatril (>480 Min., layer thickness: 0,40 mm) or butyl rubber gloves e.g. Butoject (>480 Min., layer thickness: 0,70 mm) made by KCL or gloves from other manufacturers offering the same protection.
Safety glasses with side-shields conforming to EN166
Not required; except in case of aerosol formation. Respiratory protection complying with EN 141. Recommended Filter type: A
Do not flush into surface water or sanitary sewer system. Avoid subsoil penetration.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable.
No dangerous reaction known under conditions of normal use.
None reasonably foreseeable.
Extremes of temperature and direct sunlight.
Strong acids
None reasonably foreseeable.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1903
- Shipping Name
- DISINFECTANT, LIQUID, CORROSIVE, N.O.S. (Quaternary ammonium compounds, benzyl-C12-16-alkyldimethyl, chlorides)
- Transport Class
- 8
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for terralin® protect?
The signal word is na: r-phrases.
What is the physical form of terralin® protect?
terralin® protect is a liquid appearing as liquid with green color. It has pleasant odor.
What is terralin® protect used for?
Disinfectants and general biocidal products
What is the melting point of terralin® protect?
The melting point is < -5 °C and the boiling point is ca. 90 °C.