Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TANEX GUM-EX 400 ML
- Product Code
- 40000032
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cleaning agent
Manufacturers & Suppliers
Erdal-Rex GmbH
manufacturer
Rheinallee 96 55120 Mainz
+49613196402
Emergency Contacts
Emergency Contact
+49(0)6131-19240
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Propellant
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 1,1-difluoroethane EC: 200-866-1 | 75-37-6 | --- | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water. If symptoms persist, call a physician.
Protect unharmed eye. If easy to do, remove contact lens, if worn. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. If eye irritation persists, consult a specialist.
Clean mouth with water and drink afterwards plenty of water. Do NOT induce vomiting. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician.
Immediate Medical Attention
For specialist advice physicians should contact the Poisons Information Service.
Medical Treatment
For specialist advice physicians should contact the Poisons Information Service.
Related Substances
Similar chemicals with comparable safety profiles
KEMTEX PREFILL GAS - SOLVENT 300 ML
---
TANEX POWER 10X750 ML D/F/I/NL
---
STANTEX G 7607
---
TANDEMOL ADDITIVE 24
---
MOTIP SEMI GLOSS BLACK 500 ML
---
Thixofix 40ml Tube
UFI: 6DE0-UOAR-Q00M-KDKX
MOTIP HIGH GLOSS WHITE 500 ML
---
SUPER RTV SILICONE BLACK - 200 ML
UFI: 5VJ2-V0P9-2007-0YD8
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation, especially in confined areas.
For prolonged or repeated contact use protective gloves. Chemical resistant gloves made of butyl rubber or nitrile rubber category III according to EN 374 (0,4 mm). Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact).
not required under normal use
In case of insufficient ventilation, wear suitable respiratory equipment. Recommended Filter type: ABEK-P3-filter
not required under normal use
Prevent product from entering drains. Prevent further leakage or spillage if safe to do so.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
For personal protection see section 8.
For personal protection see section 8.
For personal protection see section 8.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TANEX GUM-EX 400 ML?
The signal word is danger.
What is the physical form of TANEX GUM-EX 400 ML?
TANEX GUM-EX 400 ML is a aerosol appearing as aerosol with colourless, clear color. It has ether-like odor.
What is TANEX GUM-EX 400 ML used for?
Cleaning agent
What are the hazard statements for TANEX GUM-EX 400 ML?
This substance has 2 hazard statements:
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
What is the melting point of TANEX GUM-EX 400 ML?
The melting point is No data available and the boiling point is No information available..