Chemical Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
Congener Calibration Mix in Isooctane is a clear liquid substance commonly used laboratory chemical reference material.
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
Hazard Classifications
GHS Hazard Pictograms & Safety Symbols
GHS02
GHS07
GHS08
GHS09
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
- H225: Highly Flammable
- H302: Harmful if swallowed.
- H304: Aspiration hazard if swallowed - may be fatal if swallowed and enters airways.
- H315: Irritating to skin.
- H319: Causes severe eye irritation.
- H335: May be irritating to mucous membrane and upper respiratory system.
- H336: Vapors may cause drowsiness and dizziness.
- H400: Very toxic to aquatic life.
- H413: May cause long-term adverse effects in the aquatic environment.
Precautionary Statements
- P202: This product should only by used by persons trained in the safe handling of hazardous chemicals.
- P233: Store in a tightly closed container.
- P260: Do not breathe vapor.
- P262: Do not get in eyes, on skin or clothing.
- P264: Wash thoroughly after handling. Do not take internally. Eye wash and safety equipment should be readily available.
- P280: Protective gloves must be worn to prevent skin contact.
- P284: Respiratory Protection: If workplace exposure limit(s) of product or any component is exceeded (see TLV/PEL), or a risk assessment shows air-purifying respirators are appropriate, use of a NIOSH/MSHA approved air supplied respirator is advised. Use a full-face respirator with multi-purpose combination (US) or type ABEK (EN14387) respirator cartridges in absence of proper environmental control. Always use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Engineering and/or administrative controls should be implemented to reduce exposure.
- P331: Ingestion: Do NOT induce vomiting. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person.
- P338: Eye contact: Immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. Assure adequate flushing by separating the eyelids with fingers.
- P352: Skin contact: Wash thoroughly with soap and water. Get medical attention if irritation develops or persists.
Chemical Manufacturers & Supply Chain
Authorized suppliers, manufacturers, and distribution network information
AccuStandard, Inc.
global supplier
125 Market St. New Haven, CT 06513 USA
US
203-786-5290
203-786-5287
24/7 Emergency Response & Poison Control
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
AccuStandard, Inc.
1-203-502-7070
US
24 hours / 7 days a week
(USA)
AccuStandard, Inc.
+001-203-502-7070
US
24 hours / 7 days a week
(International)
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
mixtureGeneral Composition
Congener Calibration Mix in Isooctane
Chemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2,2',3,3',4,4',5,5'-Octachlorobiphenyl | 35694-08-7 | 0.001% | ✓ Non-hazardous |
| Decachlorobiphenyl | 2051-24-3 | 0.001% | ✓ Non-hazardous |
| 2,2',5-Trichlorobiphenyl | 37680-65-2 | 0.001% | ✓ Non-hazardous |
| 2,4,4'-Trichlorobiphenyl | 7012-37-5 | 0.001% | ✓ Non-hazardous |
| 2,4',5-Trichlorobiphenyl | 16606-02-3 | 0.001% | ✓ Non-hazardous |
| 2,2',3,5'-Tetrachlorobiphenyl | 41464-39-5 | 0.001% | ✓ Non-hazardous |
| 2,2',5,5'-Tetrachlorobiphenyl | 35693-99-3 | 0.001% | ✓ Non-hazardous |
| 2,2',4,5,5'-Pentachlorobiphenyl | 37680-73-2 | 0.001% | ✓ Non-hazardous |
| 2,3',4,4',5-Pentachlorobiphenyl | 31508-00-6 | 0.001% | ✓ Non-hazardous |
| 2,2',3,4,4',5'-Hexachlorobiphenyl | 35065-28-2 | 0.001% | ✓ Non-hazardous |
| 2,2',3,4',5',6-Hexachlorobiphenyl | 38380-04-0 | 0.001% | ✓ Non-hazardous |
| 2,2',4,4',5,5'-Hexachlorobiphenyl | 35065-27-1 | 0.001% | ✓ Non-hazardous |
| 2,2',3,3',4,4',5-Heptachlorobiphenyl | 35065-30-6 | 0.001% | ✓ Non-hazardous |
| 2,2',3,4,4',5,5'-Heptachlorobiphenyl | 35065-29-3 | 0.001% | ✓ Non-hazardous |
| Isooctane | 540-84-1 | 99.986% | ✓ Non-hazardous |
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
🫁 Inhalation Exposure
Remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel.
🖐️ Skin Contact
Wash thoroughly with soap and water.
Symptoms:
irritation develops or persists
👁️ Eye Contact
Immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. Assure adequate flushing by separating the eyelids with fingers.
🍽️ Ingestion/Swallowing
Do NOT induce vomiting. Never give anything by mouth to an unconscious person.
🚨 Immediate Medical Attention Required
Get medical assistance for all cases of overexposure. Get medical attention if irritation develops or persists. Seek immediate medical attention. Call a physician or poison control center immediately.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment (PPE)
Occupational exposure limits, engineering controls, and required safety equipment
🏭 Engineering Controls
Material must be handled or transferred in an approved fume hood or with equivalent ventilation. Engineering and/or administrative controls should be implemented to reduce exposure.
🧤 Hand Protection
Protective gloves must be worn to prevent skin contact. (Nitrile or equivalent)
👁️ Eye Protection
Use eye protection tested and approved under the appropriate government standards such as NIOSH (US) or EN 166 (EU).
😷 Respiratory Protection
If workplace exposure limit(s) of product or any component is exceeded (see TLV/PEL), or a risk assessment shows air-purifying respirators are appropriate, use of a NIOSH/MSHA approved air supplied respirator is advised. Use a full-face respirator with multi-purpose combination (US) or type ABEK (EN14387) respirator cartridges in absence of proper environmental control. Always use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
🏷️ UN Number
UN1262
📦 Proper Shipping Name
Octanes
⚠️ Transport Hazard Class
3
📋 Packing Group
II
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for Congener Calibration Mix in Isooctane?
The signal word for this substance is "danger".
What is the physical form of Congener Calibration Mix in Isooctane?
Congener Calibration Mix in Isooctane is a clear liquid appearing as clear liquid . It has mild odor odor.
What is Congener Calibration Mix in Isooctane used for?
Laboratory Chemical Reference Material
What are the hazard statements for Congener Calibration Mix in Isooctane?
This substance has 9 hazard statements: H225: Highly Flammable H302: Harmful if swallowed. H304: Aspiration hazard if swallowed - may be fatal if swallowed and enters airways. H315: Irritating to skin. H319: Causes severe eye irritation. H335: May be irritating to mucous membrane and upper respiratory system. H336: Vapors may cause drowsiness and dizziness. H400: Very toxic to aquatic life. H413: May cause long-term adverse effects in the aquatic environment.
What is the melting point of Congener Calibration Mix in Isooctane?
The melting point is -107.3 C and the boiling point is 99.2 C.