Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MR 68 C Penetrant red and fluorescent
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Testing material for nondestructive surface crack detection
Manufacturers & Suppliers
MR Chemie GmbH
manufacturer
Nordstr. 61-63 59427 Unna (Germany)
+49 (0)2303 95151 0
www.mr-chemie.de
Emergency Contacts
Emergency Contact
1 800 424 9300
Day or Night
Emergency Contact
001 703 527 3887
24h
Emergency Contact
0800-181-7059
24h
Emergency Contact
4001 204937
24h
ZH
Emergency Contact
800 968 793
24h
ZH
Emergency Contact
000 800 100 7141
24h
HI
Emergency Contact
0 800 983 611
24h
EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Butane EC: 203-448-7 | 106-97-8 | 10 - 25% | Yes |
| Distillates(petroleum),hydrotreated light EC: 265-149-8 | 64742-47-8 | 10 - 25% | Yes |
| BUTYL DIGLYCOL EC: 203-961-6 | 112-34-5 | 10 - 25% | Yes |
| Propane EC: 200-827-9 | 74-98-6 | 10 - 25% | Yes |
| 2,2',2"-nitrilotriethanol EC: 203-049-8 | 102-71-6 | 5 - 10% | Yes |
| 3',6'-Bis(diethylamino)spiro(isobenzofuran-1(3H),9'-(9H)xanthen)-3-on EC: 208-096-8 | 509-34-2 | 1 - 5% | Yes |
Propellant: Propane-Butane. For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. Then consult a doctor.
Not relevant - aerosol can.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
Grease with skin-cream to restore fat film in order to prevent skin inflammation.
Related Substances
Similar chemicals with comparable safety profiles
MR 68 NF Penetrant red and fluorescent Aerosol
---
MR 72 AF Contrast paint white (Aerosol)
---
MARKER PEN - Red
UFI: 8VGY-78AJ-A00C-RUJ5
Acid Red 26
---
MARKER PEN - Yellow
UFI: WAHY-R8SH-U00U-1JFG
MR® 76 FA Magnetic powder suspension (Aerosol)
---
Motip Fluorescent Spray
---
Acid Red 73
CAS: 5413-75-2
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
For good ventilation provide, this can be achieved by local or space exhaust.
For the protection against chemicals in areas with heightened risk of injury (mechanical hazard) no recommendation for a suitable glove material can be given. Check the permeability prior to each anewed use of the glove. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation Material of gloves Butyl rubber, BR Recommended thickness of the material: 0.5 mm The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material Value for the permeation: Level 4 Supplier for suitable protection gloves: ASD ArbeitsSicherheit Dortmund Torstr. 101 - 37355 Niederorschel OT Rdigershagen Tel.: 02301 / 919543 - Fax: 02301 / 9453893 E-Mail: m.schnellhardt@t-online.de - http://www.arbeitssicherheitdortmund.de The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses
Filter AX For good ventilation provide, this can be achieved by local or space exhaust. If the concentration lies over the job limit values, then, a certified respirator suitable for this purpose must be used.
Protective work clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2.1
- Packing Group
- Void
Warning: Gases.
Warning: Gases.
Warning: Gases.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MR 68 C Penetrant red and fluorescent?
The signal word is danger.
What is the physical form of MR 68 C Penetrant red and fluorescent?
MR 68 C Penetrant red and fluorescent is a aerosol with red color. It has characteristic odor.
What is MR 68 C Penetrant red and fluorescent used for?
Testing material for nondestructive surface crack detection
What are the hazard statements for MR 68 C Penetrant red and fluorescent?
This substance has 2 hazard statements:
- H222: Extremely flammable aerosol. Pressurised container: May burst if heated.
- H319: Causes serious eye irritation.
What is the melting point of MR 68 C Penetrant red and fluorescent?
The melting point is Undetermined. and the boiling point is Not applicable, as aerosol..