Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Alpacon multi CIP II
- Product Code
- 1899900-16
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cleaning material/ Detergent
Manufacturers & Suppliers
Alfa Laval Technologies AB
SE-221 00 Lund Sweden
+46 46 36 65 00
Emergency Contacts
CHEMTREC
+1 703-741-5970
CHEMTREC
1-800-424-9300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of the substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethoxylated alcohol C 9/11 | 68439-46-3 | 10 - 25% | Yes |
| Quaternary coco alkyl methyl amine ethoxylate methyl chloride | 863679-20-3 | 10 - 15% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Rinse opened eye for several minutes under running water and consult a doctor. Rinse cautiously with water for 20 minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Wash the mouth with water. Immediately call a doctor. If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The product is not flammable. Use fire fighting measures that suit the environment.
Not applicable.
No further relevant information available.
Use fire fighting measures that suit the environment.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapour. Small spillages (<20L) can be washed out with water into drain. (10:1) Dilute with plenty water. Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose contaminated material as waste according to item 13. Ensure adequate ventilation.
Small spillages (<20L) can be washed out with water into drain. (10:1)
Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system. Dilute with plenty of water. Do not allow to enter sewers/ surface or ground water. Send for recovery or disposal in suitable receptacles.
Small spillages (<20L) can be washed out with water into drain. (10:1) Dilute with plenty water. Absorb with liquid-binding material. Dispose contaminated material as waste according to item 13. Ensure adequate ventilation.
Materials: liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust)
Related Products
Similar products with comparable safety profiles
Alpacon Descalant III
UFI: PPK3-T0NY-C00D-NGSV
Alpacon Descalant Offshore
---
ALCUPOL F5612
CAS: 25791-96-2
ALPHAPLUS C-8
CAS: 111-66-0
AlphaPlus® C14-16-18
CAS: 1120-36-1, 629-73-2, 112-88-9
Confort C3500 Conventional Polyol
---
PANOLIN ORCON HYD ISO 32
---
Calcon 900 SC, Calcon 1000 SC, Calcon 1100 SC
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
When using do not eat or drink. Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols. When using do not eat, drink or smoke. See Section 8 for information on personal protection equipment.
Store in a dry place. Keep container tightly closed.
When using do not eat or drink. When using do not eat, drink or smoke.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: PVC gloves, Nitrile rubber, NBR, Chloroprene rubber, CR, Butyl rubber, BR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use respiratory protective device that is independent of circulating air.
Working clothes
Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system. Dilute with plenty of water. Do not allow to enter sewers/ surface or ground water. Send for recovery or disposal in suitable receptacles.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Void
- Shipping Name
- Void
- Transport Class
- Void
- Packing Group
- Void
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Alpacon multi CIP II?
The signal word is danger.
What is the solubility of Alpacon multi CIP II?
Fully miscible.
What is Alpacon multi CIP II used for?
Cleaning material/ Detergent
What are the hazard statements for Alpacon multi CIP II?
This substance has 2 hazard statements:
- H315: Causes skin irritation.
- H318: Causes serious eye damage.
What is the melting point of Alpacon multi CIP II?
The melting point is 0 °C (32 °F) and the boiling point is 100 °C (212 °F).