Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Alpacon multi CIP II
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cleaning material/ Detergent
Manufacturers & Suppliers
Alfa Laval Tumba AB
manufacturer
Hans Stahles väg 7, S-147 80 Tumba, Sweden
+46 8 530 650 00
http://www.alfalaval.com
Emergency Contacts
Emergency Contact
911
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of the substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethoxylated alcohol C 9/11 | 68439-46-3 | 10 - 25% | Yes |
| Quaternary coco alkyl methyl amine ethoxylate methyl chloride | 863679-20-3 | 10 - 15% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Generally the product does not irritate the skin.
Symptoms: Corrosive effects. Allergic reactions
Rinse opened eye for several minutes under running water and consult a doctor. Rinse cautiously with water for 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Symptoms: Can cause permanent eye damage.
Wash the mouth with water. Immediately call a doctor. If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label.
Immediate Medical Attention
Immediately call a doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The product is not flammable. Use fire fighting measures that suit the environment.
Not applicable.
No further relevant information available.
Firefighter Protection
Protective equipment: No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapour.
Small spillages (<20L) can be washed out with water into drain. (10:1) Dilute with plenty water.
Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system. Dilute with plenty of water.
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
When using do not eat or drink. When using do not eat, drink or smoke. See Section 8 for information on personal protection equipment.
Store in a dry place. Keep container tightly closed.
When using do not eat or drink. When using do not eat, drink or smoke.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use only in well-ventilated areas.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: PVC gloves, Nitrile rubber, NBR, Chloroprene rubber, CR, Butyl rubber, BR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use respiratory protective device that is independent of circulating air.
Working clothes
Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system. Dilute with plenty of water. Do not allow to enter sewers/ surface or ground water. Send for recovery or disposal in suitable receptacles.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Alpacon multi CIP II?
The signal word is danger.
What is the physical form of Alpacon multi CIP II?
Alpacon multi CIP II is a liquid appearing as form: liquid color: brown with brown color. It has nearly odorless odor.
What is Alpacon multi CIP II used for?
Cleaning material/ Detergent
What are the hazard statements for Alpacon multi CIP II?
This substance has 2 hazard statements:
- H315: Causes skin irritation.
- H318: Causes serious eye damage.
What is the melting point of Alpacon multi CIP II?
The melting point is 0 °C (32 °F) and the boiling point is 100 °C (212 °F).