Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Liebherr Spezialfett CTK
- Product Form
- Lubricating grease
- Product Code
- 18034
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricating grease
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
LIEBHERR-LOGISTICS GmbH
manufacturer
St. Vitus 1, DE - 88457 Kirchdorf an der Iller
LIEBHERR-COMPONENTS BIBERACH GmbH
manufacturer
Hans-Liebherr-Strasse 45, DE - 88400 Biberach an der Riß
LIEBHERR-WERK BIBERACH GmbH
manufacturer
Memminger Straße 120, DE - 88400 Biberach an der Riß
LIEBHERR-WERK EHINGEN GmbH
manufacturer
Dr.-Hans-Liebherr-Strasse 1, DE - 89584 Ehingen
LIEBHERR-MISCHTECHNIK GmbH
manufacturer
Im Elchgrund 12, DE - 88427 Bad Schussenried
LIEBHERR-MINING EQUIPMENT COLMAR SAS
manufacturer
49 rue Frédéric Hartmann, CS 50038, FR - 68025 Colmar Cedex
LIEBHERR-WERK NENZING GmbH
manufacturer
Dr.-Hans-Liebherr-Strasse 1, AT - 6710 Nenzing
LIEBHERR – AUSTRALIA Pty. Ltd.
manufacturer
1 Dr. Willi Liebherr Drive, Para Hills West, 5096 South Australia
Emergency Contacts
Emergency Contact
+49 (0) 73 54 / 80-6060
During working hours (CET)
CHEMTREC
1-800-424-9300
24 hours
CHEMTREC
+1-703-741-5970
24 hours
Emergency Contact
+(44)-203-8073798
Emergency Contact
+(31)-858880596
Emergency Contact
+(64)-98010034
Emergency Contact
+(61)-290372994
Emergency Contact
0-800-983-611
Emergency Contact
+1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of base oils with thickener and additives.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Zinc bis[O,O-bis(2-ethylhexyl)]bis(dithiophosphate) | 4259-15-8 | 2.5 - 5% | Yes |
| Zinc Naphthenate | 12001-85-3 | 2.5 - 5% | Yes |
The wording of the hazard symbols and H-phrases is specified in section 16 if dangerous ingredients are mentioned. Components with threshold limit values are mentioned at section 8.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Do not induce vomiting; call for medical help immediately.
Immediate Medical Attention
Call for medical help immediately.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO₂, sand, extinguishing powder. Use fire extinguishing methods suitable to surrounding conditions.
Do not use water with full jet.
In case of fire, the following can be released: Nitrogen oxides (NOx), Carbon monoxide (CO), Sulphur oxide (SOx), Phosphor oxides (PxOy)
Firefighter Protection
Wear self-contained respiratory protective device. Do not inhale explosion gases or combustion gases. Wear fully protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Particular danger of slipping on leaked/spilled product.
Do not allow to enter sewers, surface or ground water. Prevent from spreading (e.g. by damming-in or oil barriers). Inform respective authorities in case of seepage into water course or sewage system.
Pick up mechanically
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
When handling product in drums use safety footwear and suitable tools. At work please do not eat, drink or smoke.
Store only in the original receptacle. Provide floor trough without outlet. Prevent any seepage into the ground. Use only receptacles specifically permitted for this substance/product.
At work please do not eat, drink or smoke.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
If formation of steam, mist or aerosols take place the concentration in the air has to be kept at the lowest possible level.
Protective gloves. Safety gloves of nitrile rubber or viton. Preventive skin protection by use of skin-protecting agents is recommended. Material of gloves: Fluorocarbon rubber (Viton), Nitrile rubber, NBR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Penetration time of glove material: Value for the permeation: Level = 6 (480 min). The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses with side shields or chemical goggles are required.
No respiratory protection is ordinarily required under normal conditions of use. Select a filter suitable for combined particulate/ gases and organic vapours (boiling point > 65 °C, AP2, EN 14387), if exposure limit is exceeded or when aerosol or mist is formed.
Protective work clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
No further relevant information available.
Reacts with strong oxidising agents.
Avoid contact with heat, sparks, flames and all other sources of ignition. No specific data available.
No further relevant information available.
Oxides of carbon, nitrogen, sulfur and metal oxides.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Liebherr Spezialfett CTK?
The signal word is warning.
What is the physical form of Liebherr Spezialfett CTK?
Liebherr Spezialfett CTK is a pasty appearing as pasty with white color. It has characteristic odor.
What is Liebherr Spezialfett CTK used for?
Lubricating grease
What are the hazard statements for Liebherr Spezialfett CTK?
This substance has 1 hazard statement:
- H317: May cause an allergic skin reaction.
What is the melting point of Liebherr Spezialfett CTK?
The melting point is Not determined. and the boiling point is 250 °C.