Havoline Extra SAE 15W-40

If exposed to excessive levels of material in the air, move the exposed person to fresh air. If exposure to hydrogen sulfide (H2S) gas is possible during an emergency, wear an approved, positive pressure air-supplying respirator. Move the exposed person to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.

Symptoms: Coughing or respiratory discomfort.

Remove clothing and shoes if contaminated. To remove the material from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse.

Symptoms: Contact with the skin is not expected to be harmful.

Remove contact lenses, if worn, and flush eyes with water.

Symptoms: Not expected to cause prolonged or significant eye irritation.

Do not induce vomiting. As a precaution, get medical advice.

Symptoms: Not expected to be harmful if swallowed.

Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

A complex mixture of airborne solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion.

For fires involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing apparatus.

Observe all relevant local and international regulations. Keep out unnecessary and unprotected personnel. Persons entering the contaminated area to correct the problem or to determine whether it is safe to resume normal activities must comply with all instructions in the Exposure Controls/PersonalProtection section.

Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil, surface water or groundwater.

Clean up spill as soon as possible, observing precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as applying non-combustible absorbent materials or pumping.

Materials: non-combustible absorbent materials

Do not get in eyes, on skin, or on clothing. Do not taste or swallow. Do not breathe gas. Wash thoroughly after handling.

Not Applicable

Wash thoroughly after handling.

Use in a well-ventilated area.

Chemical Glove Material: Butyl (Thickness: 0.7 mm, Breakthrough Time: 120 minutes); Nitrile (Thickness: 0.8 mm, Breakthrough Time: 240 minutes); Viton Butyl (Thickness: 0.3 mm, Breakthrough Time: 240 minutes).

Wear protective equipment to prevent eye contact. Selection of protective equipment may include safety glasses, chemical goggles, face shields, or a combination depending on the work operations conducted.

No respiratory protection is normally required. If material is heated and emits hydrogen sulfide, determine if airborne concentrations are below the occupational exposure limit for hydrogen sulfide. If not, wear an approved positive pressure air-supplying respirator. For more information on hydrogen sulfide, see Chevron SDS No. 301. If user operations generate an oil mist, determine if airborne concentrations are below the occupational exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection from the measured concentrations of this material. For air-purifying respirators use a particulate cartridge.

Wear chemical personal protective equipment (PPE) to prevent skin contact. Selection of chemical protective clothing should be performed by an Occupational Hygienist or Safety Professional and be based upon applicable standards (ASTM F739 or EN 374). Using chemical PPE depends upon operations conducted and may include chemical gloves, boots, chemical apron, chemical suit, and complete facial protection. Refer to PPE manufacturers to obtain breakthrough time information to determine how long PPE can be used before it needs to be replaced.

See relevant Community environmental protection legislation or the Annex, as applicable.

This material is considered stable under normal ambient and anticipated storage and handling conditions of temperature and pressure.

May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides, etc.

Hazardous polymerization will not occur.

Not applicable

Not applicable

Alkyl Mercaptans (Elevated temperatures), Hydrogen Sulfide (Elevated temperatures)

Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal.

Contact your sales representative or local environmental or health authorities for approved disposal or recycling methods.