Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Injection Resin 86120
- Product Code
- 86120
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Structural resins, Adhesives
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
KENT (United Kingdom) Ltd
manufacturer
Forsyth House, Pitreavie Drive, Pitreavie Business Park, Dunfermline, File, KY11 8US
0800 136925
Emergency Contacts
KENT (United Kingdom) Ltd
+44 01383 723344
During normal office hours - Monday - Thursday 8.30am - 5.30pm, Friday 9.00am - 3.00pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of the substances listed below with harmless additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| vinyltoluene EC: 246-562-2 | 25013-15-4 | 1 - 10% | Yes |
| ETHYLVINYLBENZENE EC: 248-846-1 | 28106-30-1 | 1 - 10% | Yes |
| dibenzoyl peroxide EC: 202-327-6 | 94-36-0 | 5% | Yes |
| 2-ETHYLHEXYL BENZOATE EC: 226-641-8 | 5444-75-7 | 5% | Yes |
| Ethane-1,2-diol EC: 203-473-3 | 107-21-1 | 5% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of symptoms.
Instantly wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Rinse opened eye for several minutes under running water. Then consult doctor.
Do not induce vomiting; instantly call for medical help. Rinse out mouth and then drink plenty of water.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water haze. Fight larger fires with water haze or alcohol-resistant foam.
No further relevant information available.
Do not inhale explosion gases or combustion gases.
Firefighter Protection
Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow to enter drainage system, surface or ground water.
Collect mechanically. Absorb with liquid-binding material.
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
EPIKOTE™ Resin MGS LR 285
UFI: RYCF-JSKH-2FC4-C1J2
Polyurethane Resin UR5638, Part B
---
EPOFIX RESIN
---
WEVO – CASTING RESIN PU 403
---
C9-Resinfeed
CAS: 68477-54-3
SIGMASHIELD 880 BLACK 8000 RESIN
---
ULTRACRETE PY4-PY5 RESIN
UFI: WDS0-M0P6-T00V-82W8
VINKA-PLAST QD 390
CAS: 6422-86-2
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Keep away from heat and direct sunlight.
Store only in the original container. Store in cool location. Protect from heat and direct sunlight. Store in cool, dry conditions in well sealed containers.
Keep away from heat and direct sunlight.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure good ventilation. If this is not sufficient breathing protection must be used so that the vaporisation level is held under the workplace limit. Additional information about design of technical systems: No further data; see item 7.
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: Nitrile rubber, NBR. Recommended thickness of the material: ≥ 0.5 mm. Penetration time of glove material: Value for the permeation: Level ≤ 480 min (level 6). The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses recommended during refilling.
Ensure good ventilation. If this is not sufficient breathing protection must be used so that the vaporisation level is held under the workplace limit. Filter to EN 141. Filter A.
Protective work clothing. (EN-13034/6)
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known
Heat. Hot surfaces. Sources of ignition. Flames.
Alcohols, amines, aqueous acids and alkalis, Reducing agents, Heavy-metal compounds, Peroxides
Formation of toxic gases is possible during heating or in case of fire.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
Must not be disposed of together with household garbage.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Void
- Shipping Name
- Void
- Transport Class
- Void
- Packing Group
- Void
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Injection Resin 86120?
The signal word is warning.
What is the physical form of Injection Resin 86120?
Injection Resin 86120 is a pasty appearing as pasty with according to product specification color. It has characteristic odor.
What is Injection Resin 86120 used for?
Structural resins, Adhesives
What are the hazard statements for Injection Resin 86120?
This substance has 3 hazard statements:
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of Injection Resin 86120?
The melting point is Not determined and the boiling point is Not determined.