Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Eni i-Sigma performance E7 15W-40
- Product Form
- Mixture
- Product Code
- 1080
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant for internal combustion engines
Uses advised against
Recommended use are listed above; other uses are not recommended unless an assessment has provided that risks are controlled.
Manufacturers & Suppliers
Enilive S.p.A
manufacturer
Viale Giorgio Ribotta 51 - 00144 Rome Italy
+39 06 59821
Emergency Contacts
CNIT
+39 0382 24444
24h
IT, EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of hydrocarbons, Polymers, Additives
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Distillates (petroleum), solvent-dewaxed heavy paraffinic EC: 265-169-7 | 64742-65-0 | 80 - 90% | No |
| Distillates (petroleum), solvent-dewaxed light paraffinic EC: 265-159-2 | 64742-56-9 | 1 - 3% | Yes |
| Distillates (petroleum), solvent-refined light paraffinic EC: 265-091-3 | 64741-89-5 | 1 - 3% | Yes |
| Zinc bis[O-(6-methylheptyl)] bis[O-(sec-butyl)] bis(dithiophosphate) (Additive) EC: 298-577-9 | 93819-94-4 | 1 - 2% | Yes |
| Distillates (petroleum), hydrotreated heavy paraffinic EC: 265-157-1 | 64742-54-7 | 0.1 - 1.5% | Yes |
| Paraffin oils (petroleum), catalytic dewaxed heavy, Baseoil - unspecified EC: 265-174-4 | 64742-70-7 | 0.1 - 1.5% | Yes |
| Molybdenum polysulphide long chain alkyl dithiocarbamate complex (Additive) EC: 457-320-2 | --- | 0.01 - 0.15% | Yes |
Note [*]: this product has a value of DMSO extract < 3 % wt, according to IP 346. According to the criteria laid out by the EU (note L, Annex VI of Regulation (CE) 1272/2008), this product must be regarded as non carcinogenic. Note [**]: substance with occupational exposure limits for some EU countries affecting the category of mineral oils (finely refined mineral base oil mists; see section 8.1)
Notes
Composition/ Information on ingredients: Mixture of hydrocarbons Polymers Additives. Note [*]: this product has a value of DMSO extract < 3 % wt, according to IP 346. According to the criteria laid out by the EU (note L, Annex VI of Regulation (CE) 1272/2008), this product must be regarded as non carcinogenic. Note [**]: substance with occupational exposure limits for some EU countries affecting the category of mineral oils (finely refined mineral base oil mists; see section 8.1)
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of disturbances owing to inhalation of vapours or mists, remove the victim from exposure; keep at rest; if necessary, seek medical attention.
Symptoms: Overexposure to vapours may cause irritation to airways, nausea and dizziness.
Take off contaminated clothing and shoes. Wash thoroughly with soap and water. If skin irritation or rash occurs, get medical advice/attention. In case of burns, cool affected part with cold running water for at least 10 min. Cover with gauze or clean cloth. Ask for medical assistance or bring to a hospital. Do not apply salves or other substances, unless by doctor's advice. Body hypothermia must be avoided. Do not put ice on the burn.
Symptoms: Prolonged and repeated skin contact may cause reddening, irritation and dermatitis. May produce an allergic reaction. Contact with hot product may cause thermal burns.
Rinse eyes thoroughly for at least 15 minutes. Keep eyelids well apart. If irritation, blurred vision or swelling occurs and persists, obtain medical advice from a specialist. In case of burns, cool affected part with cold running water for at least 10 min. Cover with gauze or clean cloth. Ask for medical assistance or bring to a hospital. Do not apply salves or other substances, unless by doctor's advice.
Symptoms: Contact with eyes may cause temporary reddening and irritation. Contact with hot product or vapours may cause burns.
Do NOT induce vomiting. If the person is conscious, rinse mouth with water without swallowing. Keep at rest. Call for medical assistance or bring to an hospital. If the casualty is unconscious, place in the recovery position. In case of spontaneous vomiting, keep head low, to avoid the risk of aspiration into the lungs. Do not give anything by mouth to an unconscious person.
Symptoms: Accidental ingestion of small quantities of the product may cause nausea, discomfort and gastric disturbances.
Immediate Medical Attention
Obtain medical attention if casualty has an altered state of consciousness or if symptoms do not resolve. Seek medical attention in all cases of serious burns.
Medical Treatment
Immediately begin artificial respiration if breathing has ceased. Administer oxygen if necessary. Send patient to hospital.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Gloves.
Face shield. Safety glasses.
High gas/vapour concentration: gas mask with filter for organic vapours (A) or organic vapours/H2S (A+B).
Protective clothing. Safety shoes or boots.
Do not discharge the product into the environment. Storage areas/installations should be designed with adequate bunds so as to prevent ground and water pollution in case of leaks or spills. Prevent discharge of undissolved substance to or recover from onsite wastewater. Do not apply industrial sludge to natural soils. Sludge should be incinerated, contained or reclaimed.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Eni i-Sigma performance E7 15W-40?
The signal word is no signal word.
What is the physical form of Eni i-Sigma performance E7 15W-40?
Eni i-Sigma performance E7 15W-40 is a liquid appearing as clear liquid. with yellow-brown. color. It has slight odour of petroleum. odor.
What is the solubility of Eni i-Sigma performance E7 15W-40?
Water: Immiscible and insoluble
What is Eni i-Sigma performance E7 15W-40 used for?
Lubricant for internal combustion engines
What is the melting point of Eni i-Sigma performance E7 15W-40?
The melting point is Not applicable and the boiling point is 200 C (ASTM 1160).