Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
Edwards Mechanical Pump Oil - Ultragrade 15, 19, 20, 70 ****OBSOLETE**** is a pale yellow odourless liquid; does not mix with water. substance commonly used mechanical pump oil..
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
GHS Hazard Pictograms & Safety Symbols
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
Precautionary Statements
Manufacturers & Suppliers
Authorized suppliers, manufacturers, and distribution network information
Edwards
global supplier
Innovation Drive Burgess Hill West Sussex RH15 9TW United Kingdom
GB
+44 8459 212223
Edwards s.r.o.
global supplier
24/7 Emergency Response
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
CHEMWATCH EMERGENCY RESPONSE
+44 20 3901 3542
GB
CHEMWATCH EMERGENCY RESPONSE
+44 808 164 9592
GB
Once connected and if the message is not in your preferred language then please dial 01
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
mixtureGeneral Composition
mixture of severely hydrotreated and hydrocracked mineral oil
Chemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| mixture of severely hydrotreated and hydrocracked mineral oil | N/A | Not specified | Hazardous |
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
Inhalation Exposure
If fumes, aerosols or combustion products are inhaled remove from contaminated area. Other measures are usually unnecessary.
Skin Contact
Flush skin and hair with running water (and soap if available). Seek medical attention in event of irritation.
Eye Contact
Wash out immediately with water. If irritation continues, seek medical attention. Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
Ingestion/Swallowing
Immediately give a glass of water.
Immediate Medical Attention Required
If irritation continues, seek medical attention. Seek medical attention in event of irritation. If in doubt, contact a Poisons Information Centre or a doctor.
Medical Treatment
Treat symptomatically.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment
Occupational exposure limits, engineering controls, and required safety equipment
Engineering Controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection. The basic types of engineering controls are: Process controls which involve changing the way a job activity or process is done to reduce the risk. Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation that strategically "adds" and "removes" air in the work environment.
Hand Protection
Wear chemical protective gloves, e.g. PVC.
Eye Protection
Safety glasses with side shields Chemical goggles. Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing of lenses or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience.
Respiratory Protection
Type A Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI Z88 or national equivalent) Selection of the Class and Type of respirator will depend upon the level of breathing zone contaminant and the chemical nature of the contaminant. Protection Factors (defined as the ratio of contaminant outside and inside the mask) may also be important. Required minimum protection factor Maximum gas/vapour concentration present in air p.p.m. (by volume) Half-face Respirator Full-Face Respirator up to 10 1000 A-AUS / Class1 up to 50 1000 - A-AUS / Class 1 up to 50 5000 Airline * up to 100 5000 - A-2 up to 100 10000 - A-3 100+ Airline** - - Continuous Flow ** - Continuous-flow or positive pressure demand A(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 = Acid gas or hydrogen cyanide(HCN), B3 = Acid gas or hydrogen cyanide(HCN), E = Sulfur dioxide(SO2), G = Agricultural chemicals, K = Ammonia(NH3), Hg = Mercury, NO = Oxides of nitrogen, MB = Methyl bromide, AX = Low boiling point organic compounds(below 65 degC) Cartridge respirators should never be used for emergency ingress or in areas of unknown vapour concentrations or oxygen content. The wearer must be warned to leave the contaminated area immediately on detecting any odours through the respirator. The odour may indicate that the mask is not functioning properly, that the vapour concentration is too high, or that the mask is not properly fitted. Because of these limitations, only restricted use of cartridge respirators is considered appropriate. Cartridge performance is affected by humidity. Cartridges should be changed after 2 hr of continuous use unless it is determined that the humidity is less than 75%, in which case, cartridges can be used for 4 hr. Used cartridges should be discarded daily, regardless of the length of time used
Skin/Body Protection
Wear safety footwear or safety gumboots, e.g. Rubber. Overalls. P.V.C apron. Barrier cream. Skin cleansing cream.
Environmental Exposure Controls
See section 12
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for Edwards Mechanical Pump Oil - Ultragrade 15, 19, 20, 70 ****OBSOLETE****?
The signal word for this substance is "no signal word".
What is the physical form of Edwards Mechanical Pump Oil - Ultragrade 15, 19, 20, 70 ****OBSOLETE****?
Edwards Mechanical Pump Oil - Ultragrade 15, 19, 20, 70 ****OBSOLETE**** is a liquid appearing as pale yellow odourless liquid; does not mix with water. with pale yellow color. It has not available odor.
What is Edwards Mechanical Pump Oil - Ultragrade 15, 19, 20, 70 ****OBSOLETE**** used for?
Mechanical pump oil.
What is the melting point of Edwards Mechanical Pump Oil - Ultragrade 15, 19, 20, 70 ****OBSOLETE****?
The melting point is Not Available and the boiling point is Not Available.