NextSDS Logo
Safety Data Sheet EN

DYNO LILY WHITE/CRYSTAL CLEAR OIL

Scan your chemical compliance

Free 10-second scan. Upload a document and check compliance instantly.

Scan Now
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
DYNO LILY WHITE/CRYSTAL CLEAR OIL
Product Code
SO55

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Lubricating Oil

Uses advised against

Not intended for any other usage

Manufacturers & Suppliers

Merrow Superior Sewing Machine logo

Merrow Superior Sewing Machine

national supplier

502 Bedford Street Fall River, MA 02720

(212) 3691-5900

www.supsew.com

Emergency Contacts

CHEMTREC

1 800-424-9300

Day or Night

CHEMTREC

+1 703-527-3887

Day or Night

CHEMTEC MEXICO

01-800-681-9531

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

GHS Pictograms

Precautionary Statements

P201 Obtain Special Instructions Before Use.
P202 Do Not Handle Until All Safety Precautions Are Understood.
P281 Use Personal Protective equipment
P308 If Exposed Or Concerned: Get Medical Advice/attention.
P405 Store Locked Up.
P501 Dispose of container according to regional regulations

Manage your Safety Data Sheets

Organize and access chemical safety data with ease

Manage SDS
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Products containing mineral oil with less than 3% DMSO extract as measured by IP-346.

Chemical Name CAS Number Concentration Hazardous
LUBRICANT BASE OIL (PETROLEUM) 64742-88-4 95 - 100% No
paraffinehoudende EC: 265-157-1 64742-54-7 --- No
residu-olin (aardolie), solvent-geraffineerd EC: 265-101-6 64742-01-4 --- No

Notes

INERT The remaining percentages are not listed as Physical or Health Hazards (29 CFR 1910.1200)

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove victim to fresh air and keep at rest in a position comfortable for breathing. If breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. Maintain an open airway.

Eye contact

Immediately flush eyes with plenty of water occasionally lifting the upper and lower eyelids. Check and remove any contact lenses. Continue to rinse for at least 20 minutes.

Ingestion

Wash out mouth with water. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs.

Immediate Medical Attention

Contact poison specialist if product has been ingested.

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

The data for this section has not been processed yet.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

The data for this section has not been processed yet.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

The data for this section has not been processed yet.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Material should be handled in enclosed vessels and equipment, in which case general room ventilation should be sufficient. Local exhaust ventilation should be used at points where dust, mist, vapors or gases can escape into the room air. No special requirements under ordinary conditions of use and with adequate ventilation.

Hands

Butyl rubber. Use nitrile or neoprene gloves.

Eyes

If contact is likely, safety glasses with side shields are recommended.

Respiratory

Use a properly fitted air purifying or supplied air respirator complying with an approved standard if a risk assessment indicates this a necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator.

Skin/Body

Use good industrial hygiene practices. In case of skin contact, wash hands and arms with soap and water. Use caution when opening manway covers of storage and transportation containers. 3-nitroaniline crystals may be present on the interior surface of these openings. 3-nitroaniline is toxic by dermal exposure.

Environmental

General room ventilation should be satisfactory. Local exhaust ventilation may be necessary if misting is generated.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Metal Corrosion
---
Colour
B&C
Physical State
Liquid
Flammability
Not Applicable
Evaporation Rate
No Data Available
Solubility In Water
Negligible, 0-1%
Crystallisation Point
---
Relative Density
0.86
Decomposition Temperature
Not Determined
Odor
Characteristic of Petroleum
Cloud Point
---
Lower Explosive Limit
No Data Available
Flash Point
221C
Partition Coefficient
No Data Available
Auto Ignition Temperature
Not Determined
Appearance
---
Melting Point
---
Solubility In Fat
---
Ph
No Data Available
Properties Status
---
Molecular Weight
---
Solidification Point
---
Vapor Density
> 1
Odor Threshold
No Data Available
Relative Evaporation Rate
---
Vapor Pressure
< 1 mm Hg
Form
---
Softening Point
---
Voc Content
---
State Under Standard Conditions
---
Explosive Limits
---
Freezing Point
No Data Available
Colour Intensity
---
Boiling Point
No Data Available
Solubility
---
Physical State Data
liquid
Density
---
Upper Explosive Limit
No Data Available
Bulk Density
---
Kinematic Viscosity
---
Dynamic Viscosity
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

The data for this section has not been processed yet.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for DYNO LILY WHITE/CRYSTAL CLEAR OIL?

The signal word is no signal word.

What is the physical form of DYNO LILY WHITE/CRYSTAL CLEAR OIL?

DYNO LILY WHITE/CRYSTAL CLEAR OIL is a liquid with b&c color. It has characteristic of petroleum odor.

What is DYNO LILY WHITE/CRYSTAL CLEAR OIL used for?

Lubricating Oil

Compliance Scanner

Scan your compliance