Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Evyron™ T20 molten
- Chemical Name
- Propylidynetrimethanol
Regulatory Identifiers
- CAS Number
- 77-99-6 Check regulations →
- EC Number
- 201-074-9 Check regulations →
- REACH No.
- 01-2119486799-10-0005
Identified Uses
in adhesives, in sealants, in coatings, in inks, in lubricants, in greases, in metal working fluids, in polishes, in wax-blends, in laboratories, for surface treatment of pigments and pigment concentrates, for polymers and plastics (PVC heat stabilizers) Manufacture: of elastomers, of non-metallic mineral products, of polymers including resins, of oligomers.
Uses advised against
Not identified.
Manufacturers & Suppliers
Perstorp Specialty Chemicals AB
manufacturer
SE-284 80 Perstorp, Sweden
+46 435 380 00
http://www.perstorp.com
Emergency Contacts
Emergency Contact
(+1) 760 476 3961 (contract no: 334101)
Emergency Contact
(+44 8 08 189 0979 (contract no: 334101)
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
This product does not contain candidate substances of very high concern at a concentration >=0.1% (Regulation (EC) No. 1907/2006 (REACH), Article 59)
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Propylidynetrimethanol EC: 201-074-9 | 77-99-6 | 90 - 100% | Yes |
No information available.
Notes
Classification according to Regulation (EC) No. 1272/2008 [CLP] - Notes [A] - Not classified, Data are conclusive but insufficient for classification Full text of H- and EUH-phrases: see section 16
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove to fresh air. Rinse mouth with water. If irritation persists get medical advice/attention.
In contact with molten product immediately flush with cold water for at least 10 minutes. Do not pull solidified product off the skin. In case of burn injury immediately get medical attention.
Symptoms: thermal burns
After contact with the molten/hot product, cool rapidly using water. Seek immediate medical attention/advice.
Rinse mouth then drink plenty of water. Seek immediate medical attention/advice.
Immediate Medical Attention
In case of burn injury immediately get medical attention. Seek immediate medical attention/advice for eye contact and ingestion.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
All types of extinguishing media are suitable. Use fire extinguishing methods suitable to surrounding conditions.
Do not use a solid water stream as it may scatter and spread fire.
Thermal decomposition can lead to release of irritating and toxic gases and vapours.
Use water spray jet to protect personnel and to cool endangered containers.
Firefighter Protection
Wear self-contained breathing apparatus and protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unprotected persons away from molten/hot product if released. Avoid contact with skin, eyes and inhalation of vapours.
Do not allow into any sewer, on the ground or into any body of water.
Absorb with earth, sand or other non-combustible material and transfer to containers for later disposal.
Materials: earth, sand or other non-combustible material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Not to be used by pregnant workers and workers who have recently given birth or who are breastfeeding. Ensure adequate ventilation. Design work place in such a way that splashes from hot product is prevented. Use personal protection recommended in
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Emergency shower and eye wash facilities must exist in the work place. Ensure adequate ventilation.
Wear protective gloves. Heat resistant gloves are recommended when handling molten materials. Ensure that the breakthrough time of the glove material is not exceeded. Refer to glove supplier for information on breakthrough time for specific gloves. Gloves must conform to standard EN 374. /. ANSI/ISEA 105-2016.
Tight sealing safety goggles. Face protection shield.
If technical exhaust or ventilation measures are not possible or insufficient, respiratory protection must be worn. APF 10; 90%.
Wear appropriate personal protective clothing to prevent skin contact. If any risk of getting in contact with hot product - wear heat-resistant protective clothing.
Not determined.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
There exists no specific test data for this product. For further information, see the subsequent subsections of this chapter.
No dangerous reactions known under normal conditions of use.
None under normal use conditions.
None known.
Thermal decomposition can lead to release of irritating and toxic gases and vapours; Carbon monoxide (CO), Carbon dioxide (CO2).
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Incinerate at a licensed installation.
Incinerate at a licensed installation.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN3257
- Shipping Name
- Elevated temperature liquid, n.o.s.
- Transport Class
- 9
- Packing Group
- III
232, 274
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Evyron™ T20 molten?
The signal word is warning.
What is the physical form of Evyron™ T20 molten?
Evyron™ T20 molten is a liquid with colourless color. It has slight odor.
What is the solubility of Evyron™ T20 molten?
No information available
What is Evyron™ T20 molten used for?
in adhesives, in sealants, in coatings, in inks, in lubricants, in greases, in metal working fluids, in polishes, in wax-blends, in laboratories, for surface treatment of pigments and pigment concentrates, for polymers and plastics (PVC heat stabilizers) Manufacture: of elastomers, of non-metallic mineral products, of polymers including resins, of oligomers.
What are the hazard statements for Evyron™ T20 molten?
This substance has 1 hazard statement:
- H361fd: Suspected of damaging fertility. Suspected of damaging the unborn child
What is the melting point of Evyron™ T20 molten?
The melting point is 57-62 °C and the boiling point is 302 °C.