NextSDS Logo
Safety Data Sheet EN

LOCTITE TITEFOAM Gaps and Cracks 12oz

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE TITEFOAM Gaps and Cracks 12oz
Product Form
Foam, 1-component with propellant gas
Product Code
1988753

Regulatory Identifiers

CAS Number
N/A

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

GHS Pictograms

Precautionary Statements

Not prescribed
Not prescribed
Not prescribed
Not prescribed

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Notes

Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, immediately remove the affected person to fresh air. If symptoms develop and persist, get medical attention. If inhaled, immediately remove the affected person to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.

Skin contact

Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention. Fresh foam: Wipe off affected skin area immediately with a soft cloth and then remove residues with vegetable oil; apply skin care product. Cured foam can be removed only mechanically. Immediately wash skin thoroughly with soap and water. Remove contaminated clothes.

Eye contact

In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention. Flush eyes with plenty of water for at least 5 minutes. If irritation persists seek medical attention.

Symptoms: irritation

Ingestion

Get immediate medical attention. Do not induce vomiting. Do not induce vomiting, seek medical advice immediately.

Immediate Medical Attention

Get immediate medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide. Foam, dry chemical or carbon dioxide.

Specific hazards

May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses. Cool aerosol containers with jet of water. Containers may explode. Contents under pressure.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus. Wear a self-contained breathing apparatus with a full face piece operated in pressure-demand or other positive pressure mode. Wear protective equipment.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Allow to solidify. Scrape up spilled material and place in a closed container for disposal. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust).

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid breathing vapors or mists of this product. Ground and bond all equipment as required (when transferring products). For industrial use only. Do not take internally. Keep away from heat, spark and flame. Do not puncture or incinerate pressurized containers. Ensure adequate ventilation, especially in confined areas. Keep out of the reach of children. When using do not eat, drink or smoke. Wear suitable protective clothing, gloves and eye/face protection.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store between 10°C and 27°C. Do not store above 49 °C.

Hygiene

Wash thoroughly after handling. When using do not eat, drink or smoke.

Fire prevention

Keep away from heat, spark and flame. Store away from heat, sparks, flames, or other sources of ignition.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Freezing Point
---
Boiling Point
-42 °C (-43.6 °F) Values referring to propellant-42 °C (-43.6 °F) Compressed Gas.
Voc Content
19.28 %; 208.6 g/l (by weight, calculated using CARB method; g/L less water, less exempts calculated using SCAQMD method)
Relative Evaporation Rate
---
Dynamic Viscosity
Not available.
Cloud Point
---
Melting Point
Not applicable, Product is a liquid
Bulk Density
---
Solubility In Water
---
Relative Density
---
Decomposition Temperature
Not available.
Molecular Weight
---
State Under Standard Conditions
---
Flammability
Extremely flammable aerosol.
Vapor Density
---
Appearance
---
Upper Explosive Limit
32 % The product is not explosive. The formation of explosive vapor/air mixtures is possible.
Solidification Point
---
Properties Status
---
Odor
Mild, Ether
Physical State Data
aerosol
Lower Explosive Limit
1.5 % 0.4 % The product is not explosive. The formation of explosive vapor/air mixtures is possible.
Solubility In Fat
---
Flash Point
Not applicable
Auto Ignition Temperature
Not available.
Explosive Limits
---
Vapor Pressure
0.5 MPa (20 °C (68°F)) Referring to liquefied propellant at 20 °C > 100 mm hg (20 °C (68°F))
Kinematic Viscosity
> 20.5 mm2/s
Density
1.107
Metal Corrosion
---
Partition Coefficient
Not available.
Colour Intensity
---
Crystallisation Point
---
Softening Point
---
Solubility
Reacts slowly with water to liberate carbon dioxide gas. Water
Colour
Off white
Form
---
Ph
Not applicable, Product reacts with water.
Evaporation Rate
10 (Butyl acetate = 1)
Odor Threshold
Not available.
Physical State
Aerosol
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing. May occur.

Avoid

Keep away from heat, ignition sources and incompatible materials. Keep away from sources of ignition and naked flames.

Incompatible

This product may react with strong acids or oxidizing agents. Alcohols. Metal compounds. Strong bases. Water.

Decomposition

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen. Carbon dioxide, carbon monoxide and irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion. nitrogen oxides

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN1950
Shipping Name
Aerosols
Transport Class
2.1
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE TITEFOAM Gaps and Cracks 12oz?

The signal word is no signal word.

What is the physical form of LOCTITE TITEFOAM Gaps and Cracks 12oz?

LOCTITE TITEFOAM Gaps and Cracks 12oz is a aerosol with off white color. It has mild, ether odor.

What is the solubility of LOCTITE TITEFOAM Gaps and Cracks 12oz?

Reacts slowly with water to liberate carbon dioxide gas. Water

What is the melting point of LOCTITE TITEFOAM Gaps and Cracks 12oz?

The melting point is Not applicable, Product is a liquid and the boiling point is -42 °C (-43.6 °F) Values referring to propellant-42 °C (-43.6 °F) Compressed Gas..