Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm
- Product Code
- NG04SO3303
- Chemical Name
- Stannic oxide
- Synonyms
- Tin Oxide
Regulatory Identifiers
- CAS Number
- 18282-10-5 Check regulations →
- EC Number
- 242-159-0 Check regulations →
- REACH No.
- 01-2119946062-44
Identified Uses
Research
Manufacturers & Suppliers
Nanografi Nanotechnology
national supplier
ODTÜ Teknokentİkizler Binası B-1/H ODTÜ Teknokent 06531- ANKARA
Emergency Contacts
Emergency Contact
+90 312 285 85 09
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Tin (IV) oxide | 18282-10-5 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air. If required, provide artificial respiration. Keep patient warm. Seek immediate medical advice.
Immediately wash with water and soap and rinse thoroughly. Seek immediate medical advice.
Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Handle in accordance with good industrial hygiene and safety practice.
For any handling steps where the substance is in particulate form or in a suspension with pure water where the substance is not solubilized, the gloves must be comprised of material that successfully passes ASTM F-1671. For any handling steps where the substance is part of a carrier liquid, other than the aqueous suspension noted in the previous paragraph, gloves must be comprised of material that successfully passes ASTM F-739 (continuous liquid contact method). Gloves must be changed before they show degradation and before the designated breakthrough time for the carrier liquid (as determined by the ASTM F-739 testing or by the manufacturer). Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
Safety glasses with side-shields conforming to EN166 Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
The EPA mandates the use of full face respirators with minimum N100 grade cartridges if there is any risk of exposure to the dust. For nuisance exposures use type P95 (US) or type P1 (EU EN 143) particle respirator. For higher level protection use type OV/AG/P99 (US) or type ABEK-P2 (EU EN 143) respirator cartridges. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Impervious clothing, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
No dangerous reactions known.
No data available.
No data available.
no data available – In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm known by?
Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm is also known as: Tin Oxide
What is the hazard signal word for Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm?
The signal word is no signal word.
What is the physical form of Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm?
Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm is a solid appearing as solid . It has no data available odor.
What is Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm used for?
Research
What is the melting point of Tin Oxide (SnO2) Nanopowder/Nanoparticles, Purity: 99.97%, Size: 430 nm?
The melting point is no data available and the boiling point is no data available.