Chemical Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
DIRECT TO RUST METAL PAINT SATIN commonly used solvent borne coating for interior and exterior use..
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
Hazard Classifications
GHS Hazard Pictograms & Safety Symbols
GHS02
GHS07
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
- H226: Flammable liquid and vapour.
- H336: May cause drowsiness or dizziness.
- H412: Harmful to aquatic life with long lasting effects.
Precautionary Statements
- P102: Keep out of reach of children.
- P101: If medical advice is needed, have product container or label at hand.
- P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P233: Keep container tightly closed.
- P262: Do not get in eyes, on skin, or on clothing.
- IF INHALED: Remove person to fresh air and keep comfortable for breathing.
- P312: Call a POISON CENTER or doctor if you feel unwell.
- P235: Keep cool.
- P501: Dispose of contents and container in accordance with all local, regional, national or international regulations.
Chemical Manufacturers & Supply Chain
Authorized suppliers, manufacturers, and distribution network information
ICI Paints AkzoNobel
national supplier
24/7 Emergency Response & Poison Control
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
Emergency Contact
Slough +44 (0) 1753 550000
GB
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
MixtureGeneral Composition
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment, are PBTs, vPvBs or Substances of equivalent concern, or have been assigned a workplace exposure limit and hence require reporting in this section.
Chemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Hydrocarbons, C9-C11, n- alkanes, isoalkanes, cyclics, < 2% aromatics EC: 919-857-5 | N/A | 25-50% | ⚠️ Hazardous |
| trizinc bis(orthophosphate) EC: 231-944-3 | 7779-90-0 | 1-2.5% | ⚠️ Hazardous |
| Hydrocarbons, C9-C10, n- alkanes, isoalkanes, cyclics, <2% aromatics | N/A | 1-3% | ⚠️ Hazardous |
| Hydrocarbons, C10-C13, n- alkanes, isoalkanes, cyclics, < 2% aromatics EC: 918-481-9 | N/A | 0.5-1% | ⚠️ Hazardous |
| 2-butanone oxime EC: 202-496-6 | 96-29-7 | 0.3-1% | ⚠️ Hazardous |
Additional Information
Occupational exposure limits, if available, are listed in Section 8.
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
🫁 Inhalation Exposure
Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
Symptoms:
Exposure to component solvent vapour concentrations in excess of the stated occupational exposure limit may result in adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the kidneys, liver and central nervous system. Symptoms and signs include headache, dizziness, fatigue, muscular weakness, drowsiness and, in extreme cases, loss of consciousness.
🖐️ Skin Contact
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water or use recognised skin cleanser. Do NOT use solvents or thinners.
Symptoms:
Solvents may cause some of the above effects by absorption through the skin. Repeated or prolonged contact with the mixture may cause removal of natural fat from the skin, resulting in non-allergic contact dermatitis and absorption through the skin.
👁️ Eye Contact
Remove contact lenses, irrigate copiously with clean, fresh water, holding the eyelids apart for at least 10 minutes and seek immediate medical advice.
Symptoms:
If splashed in the eyes, the liquid may cause irritation and reversible damage.
🍽️ Ingestion/Swallowing
If swallowed, seek medical advice immediately and show the container or label. Keep person warm and at rest. Do NOT induce vomiting.
Symptoms:
Ingestion may cause nausea, diarrhea and vomiting.
🚨 Immediate Medical Attention Required
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Medical Treatment
No specific treatment.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment (PPE)
Occupational exposure limits, engineering controls, and required safety equipment
🏭 Engineering Controls
Provide adequate ventilation. Where reasonably practicable, this should be achieved by the use of local exhaust ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates and solvent vapours below the OEL, suitable respiratory protection must be worn.
🧤 Hand Protection
For prolonged or repeated contact use protective gloves. Barrier creams may help to protect the exposed areas of skin, they should however not be applied once exposure has occurred. Skin should be washed after contact. Use chemical resistant gloves classified under Standard EN 374: Protective gloves against chemicals and micro-organisms. Recommended gloves: Viton or Nitrile Breakthrough Time: 480 min When prolonged or frequently repeated contact may occur, a glove with a protection class of 6 (breakthrough time greater than 480 minutes according to EN 374) is recommended. When only brief contact is expected, a glove with a protection class of 2 or higher (breakthrough time greater than 30 minutes according to EN 374) is recommended. NOTICE: The selection of a specific glove for a particular application and duration of use in a workplace should also take into account all relevant workplace factors such as, but not limited to: Other chemicals which may be handled, physical requirements (cut/puncture protection, dexterity, thermal protection), potential body reactions to glove materials, as well as the instructions/specifications provided by the glove supplier. The user must check that the final choice of type of glove selected for handling this product is the most appropriate and takes into account the particular conditions of use, as included in the user's risk assessment.
👁️ Eye Protection
Use safety eyewear designed to protect against splash of liquids.
😷 Respiratory Protection
If workers are exposed to concentrations above the exposure limit, they must use appropriate, certified respirators. OLD LEAD-BASED PAINTS: When surfaces are to be prepared for painting, account should be taken of the age of the property and the possibility that lead-pigmented paint might be present. There is a possibility that ingestion or inhalation of scrapings or dust arising from the preparation work could cause health effects. As a working rule you should assume that this will be the case if the age of the property is pre 1960. Where possible wet sanding or chemical stripping methods should be used with surfaces of this type to avoid the creation of dust. When dry sanding cannot be avoided, and effective local exhaust ventilation is not available, it is recommended that a dust respirator is worn, that is approved for use with lead dusts, and its type selected on the basis of the COSHH assessment, taking into account the Workplace Exposure Limit for lead in air. Furthermore, steps should be taken to ensure containment of the dusts created, and that all practicable measures are taken to clean up thoroughly all deposits of dusts in and around the affected area. Respiratory protection in case of dust or spray mist formation. (particle filter EN143 type P2) Respiratory protection in case of vapour formation. (half mask with combination filter A2-P2 til concentrations of 0,5 Vol%.) Extra precautions will also need to be taken when burning off old lead-based paints because fumes containing lead will be produced. It is recommended that a respirator, approved for use with particulate fumes of lead is selected on the basis of the COSHH assessment, taking into account the Workplace Exposure Limit for lead in air. Similar precautions to those given above about sanding should be taken with reference to protective clothing, disposal of scrapings and dusts, and exclusion of other personnel and especially children from the building during actual work and the subsequent clean up operations. Avoid the inhalation of dust. Wear suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead.
🦺 Skin/Body Protection
Personnel should wear antistatic clothing made of natural fibres or of high-temperature-resistant synthetic fibres. Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. The current Control of Lead at Work Regulations approved code of practice should be consulted for advice on protective clothing and personal hygiene precautions.
🌍 Environmental Exposure Controls
Do not allow to enter drains or watercourses.
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
🏷️ UN Number
UN1263
📋 Packing Group
III
🚛 ADR Transport Precautions
Transport within user's premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage.
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for DIRECT TO RUST METAL PAINT SATIN?
The signal word for this substance is "warning".
What is the physical form of DIRECT TO RUST METAL PAINT SATIN?
DIRECT TO RUST METAL PAINT SATIN is a liquid. with not available. color. It has not available. odor.
What is the solubility of DIRECT TO RUST METAL PAINT SATIN?
Insoluble in the following materials: cold water.
What is DIRECT TO RUST METAL PAINT SATIN used for?
Solvent borne coating for interior and exterior use.
What are the hazard statements for DIRECT TO RUST METAL PAINT SATIN?
This substance has 3 hazard statements: H226: Flammable liquid and vapour. H336: May cause drowsiness or dizziness. H412: Harmful to aquatic life with long lasting effects.
What is the melting point of DIRECT TO RUST METAL PAINT SATIN?
The melting point is Not available. and the boiling point is 149C.