Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Nital, Salpetersäure 5 %, alkoholisch
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Laboratory chemicals
Uses advised against
Any non-intended use.
Manufacturers & Suppliers
CRIDA-Chemie
manufacturer
Johannesstr. 34, D-57482 Wenden
02762/417771
Dr. Gans-Eichler Chemieberatung GmbH
Raesfeldstr. 22, 48149 Münster
+49(0)251/394868-69
Emergency Contacts
Emergency Contact
+49 (0) 170 2450126
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| ethanol, ethyl alcohol EC: 200-578-6 | 64-17-5 | 70% | Yes |
| Nitric acid ... % EC: 231-714-2 | 7697-37-2 | 5% | Yes |
Product does not contain listed SVHC substances > 0,1 % according to Regulation (EC) No. 1907/2006 Article 59 (REACH)
Notes
Full text of H and EUH statements: see section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Provide fresh air. In case of allergic symptoms, especially in the breathing area, seek medical advice immediately. Apply cortisone spray at early stage.
Symptoms: acute danger of asphyxia due to spasm or glottis at high doses of nitrous gases by inhalation., Prolonged and repeated inhalation of decomposition products may cause a pulmonary oedema .. In case of allergic symptoms, especially in the breathing area.
Remove contaminated, saturated clothing immediately. After contact with skin, wash immediately with plenty of water and soap. Call a physician immediately.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Consult an ophthalmologist.
Symptoms: Corroded eyes.
Rinse mouth thoroughly with water. Let water be drunken in little sips (dilution effect). Do NOT induce vomiting. Call a physician immediately.
Immediate Medical Attention
In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible). In case of allergic symptoms, especially in the breathing area, seek medical advice immediately. Call a physician immediately.
Medical Treatment
Corroded eyes (again) rinse several minutes with Isogutt or water; Thereafter 5-10% ascorbic acid and tolazoline be dropped. Affected skin should be applied after thorough flushing with Dermatocorticoid. after inhalation of acid mists or nitrogen oxides released is indispensable for the immediate topical and parenteral Glucocorticoidapplikation, depending on findings if required intubation or tracheotomy and oxygen ventilator.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Salpetersäure 60 %
---
Sodium hydroxide solution 45 %, extra pure
---
Alkaline Alcohol
---
Ethanol ≥70 %, denatured
UFI: 55H0-A0HQ-M009-656S
2-Propanol 70 %, pure
CAS: 67-63-0
Formic acid 30 %, pure
UFI: R5U3-P0T3-5004-YTG6
Formaldehyde solution ≥37 %, Ph. Eur., USP, BP
---
Alcoholic Formalin 30 percent
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate ventilation as well as local exhaustion at critical locations.
In case of prolonged or frequently repeated skin contact: Wear suitable gloves. Suitable material: Butyl rubber. Thickness of glove material: 0,5 mm Breakthrough time >= 480 min. penetration time (maximum wearing period): ~ 120 min. (estimated) In the case of wanting to use the gloves again, clean them before taking off and air them well. Before using check leak tightness / impermeability. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.
Recommended eye protection brand: Tightly sealed safety glasses. (DIN EN 166)
With correct and proper use, and under normal conditions, breathing protection is not required. Respiratory protection necessary at: exceeding exposure limit values Insufficient ventilation. Suitable respiratory protective equipment: Combination filtering device (EN 14387) Type AEB-P3 The filter class must be suitable for the maximum contaminant concentration (gas/vapour/aerosol/particulates) that may arise when handling the product. If the concentration is exceeded, self-contained breathing apparatus must be used.
Wear fire/flame resistant/retardant clothing. Minimum standard for preventive measures while handling with working materials are specified in the TRGS 500 (D).
Do not allow uncontrolled discharge of product into the environment.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN 2924
- Shipping Name
- FLAMMABLE LIQUID, CORROSIVE, N.O.S.
- Transport Class
- 3
- Packing Group
- II
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Nital, Salpetersäure 5 %, alkoholisch?
The signal word is danger.
What is the physical form of Nital, Salpetersäure 5 %, alkoholisch?
Nital, Salpetersäure 5 %, alkoholisch is a liquid with colourless color. It has alcohol odor.
What is the solubility of Nital, Salpetersäure 5 %, alkoholisch?
not determined
What is Nital, Salpetersäure 5 %, alkoholisch used for?
Laboratory chemicals
What are the hazard statements for Nital, Salpetersäure 5 %, alkoholisch?
This substance has 3 hazard statements:
- H225: Highly flammable liquid and vapour.
- H290: May be corrosive to metals.
- H314: Causes severe skin burns and eye damage.
What is the melting point of Nital, Salpetersäure 5 %, alkoholisch?
The melting point is -114,5 and the boiling point is 78.