2-K WB RENNERPLAST FOR PVC, BY SPRAY, RAL7016-LIKE

Get medical advice/attention immediately. Remove victim to fresh air, away from the accident scene. If the subject stops breathing, administer artificial respiration. Take suitable precautions for rescue workers.

Remove contaminated clothing. Rinse skin with a shower immediately. Get medical advice/attention.

Remove contact lenses, if present. Wash immediately with plenty of water for at least 30-60 minutes, opening the eyelids fully. Get medical advice/attention.

Have the subject drink as much water as possible. Get medical advice/attention. Do not induce vomiting unless explicitly authorised by a doctor.

carbon dioxide, foam, powder and water spray.

None in particular.

METHYL METHACRYLATE: Heat may cause the product to polymerise, which could lead to explosion.

Use jets of water to cool the containers to prevent product decomposition and the development of substances potentially hazardous for health.

Block the leakage if there is no hazard.

The product must not penetrate into the sewer system or come into contact with surface water or ground water.

Absorb the remainder with inert absorbent material.

Materials: inert absorbent material

Before handling the product, consult all the other sections of this material safety data sheet. Avoid leakage of the product into the environment. Do not eat, drink or smoke during use. Remove any contaminated clothes and personal protective equipment before entering places in which people eat.

Store only in the original container. Store the containers sealed, in a well ventilated place, away from direct sunlight.

Do not eat, drink or smoke during use. Remove any contaminated clothes and personal protective equipment before entering places in which people eat.

Primary collective protective measures such as adequate natural ventilation and local extraction

Use category III chemical resistant gloves according to the EN 374 standard. Brief contact (splash protection) – non-exhaustive list. Suitable material: NITRILE RUBBER (NBR). Glove thickness: greater than 0.4 mm. Breakthrough time: from 30 to 60 minutes. Breakthrough index: at least 2. The gloves must be replaced if there are signs of deterioration.

Wear safety mask glasses (EN 166).

Use a mask with EN140 and/or EN136 approval, with an ABEK type filter (EN 14387)

Wear work clothes and safety footwear that complies with EN ISO 20344

The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards. Product residues must not be indiscriminately disposed of with waste water or by dumping in waterways.

The product is stable in normal conditions of use and storage.

There are no particular risks of reaction with other substances in normal conditions of use. AMMONIA: Corrodes: aluminium, iron, zinc, copper, copper alloys. 2-BUTOXYETHANOL: Decomposes under the effect of heat. ETHYL ACETATE: May react with: acids, bases, strong oxidants. Attacks: aluminium. Decomposes slowly into acetic acid and ethanol under the effect of light, air and water.

No hazardous reactions are foreseeable in normal conditions of use and storage. AMMONIA: Risk of explosion on contact with: strong acids, iodine. May react dangerously with: strong bases. METHYL METHACRYLATE: May polymerise on contact with: ammonia, organic peroxides, persulphates. Risk of explosion on contact with: dibenzoyl peroxide, diterbutyl peroxide, propionaldehyde. May react dangerously with: strong oxidising agents. Forms explosive mixtures with: air. CYCLOHEXANE: May react violently with: strong oxidants, liquid nitric oxide. Forms explosive mixtures with: air. 2-BUTOXYETHANOL: May react dangerously with: aluminium, oxidising agents. Forms peroxides with: air. ETHYL ACETATE: Risk of explosion on contact with: alkaline metals, hydrides, oleum. May react violently with: fluorine, strong oxidising agents, chlorosulphuric acid, potassium tert-butoxide. Forms explosive mixtures with: air. DIETHYLENE GLYCOL MONOETHYL ETHER: it can form explosive mix with air in presence of high temperature (T > 94°C)

None in particular. However the usual precautions used for chemical products should be respected. METHYL METHACRYLATE: Avoid exposure to: heat, UV rays. Avoid contact with: oxidising substances, reducing substances, acids, bases. 2-BUTOXYETHANOL: Avoid exposure to: sources of heat, naked flames. ETHYL ACETATE: Avoid exposure to: light, sources of heat, naked flames.

AMMONIA: Incompatible with: silver, silver salts, lead, lead salts, zinc, zinc salts, hydrochloric acid, nitric acid, oleum, halogens, acrolein, nitromethane, acrylic acid. CYCLOHEXANE: Incompatible materials: natural rubbers, neoprene, polyvinyl chloride, polyethylene. 2-BUTOXYETHANOL: Incompatible with: oxidising substances, alkaline substances, light metals. ETHYL ACETATE: Incompatible with: acids, bases, strong oxidants, aluminium, nitrates, chlorosulphuric acid. Incompatible materials: plastic materials. 1-ETHYL-2-PYRROLIDINONE: Materials to avoid: Strong oxidizing agents, Strong acids, Strong bases, Acyl chlorides.

AMMONIA: May develop: nitric oxide. METHYL METHACRYLATE: When heated to decomposition releases: harsh fumes, zinc alloys. 2-BUTOXYETHANOL: May develop: hydrogen. ETHYL ACETATE: When heated to decomposition releases: harsh fumes, irritating vapours.

Disposal must be carried out by an authorised waste management company.

For disposal or recovery in EU countries, use the relevant waste code (EWC code) identified in the European Waste Catalogue. The producer of the waste must assign the EWC code according to the sector and type of process.