Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- SR-Dur 2478 M
- Product Code
- 9000-1137
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Epoxy curing agent
Manufacturers & Suppliers
SRS-Meeder Synthetic Resin Systems GmbH
manufacturer
St. Johanniskoog-Ring 7 D-25836 Poppenbüll, Germany
http://www.srs-meeder.de
Department: product safety
+49-4862-1044-890
Emergency Contacts
Emergency Contact
+49-4862-1044-890
only available during office hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
If symptoms persist consult doctor.
Medical Treatment
Treat according to symptoms (decontamination, vital functions).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. CO2, sand, extinguishing powder. Do not use water.
Water, Water with full jet
In case of fire, the following can be released: Nitrogen oxides (NOx) Carbon monoxide (CO). Under certain fire conditions, traces of other toxic gases cannot be excluded.
Firefighter Protection
Mount respiratory protective device. Wear self-contained breathing apparatus and chemical-protective clothing
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow to enter sewers/ surface or ground water.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Keep container tightly sealed.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Protective gloves. Avoid direct contact with the chemical/ the product/ the preparation by organizational measures. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Butyl rubber, BR Nitrile rubber, NBR Recommended thickness of the material: ≥ 0,7 mm. Penetration time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed. For the mixture of chemicals mentioned below the penetration time has to be at least 480 minutes (Permeation according to EN 374 Part 3: Level 6).
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use selfcontained respiratory protective device. Use suitable respiratory protective device when high concentrations are present.
Body protection must be chosen depending on activity and possible exposure, e.g. apron, protecting boots, chemicalprotection suit (according to EN 14605 in case of splashes or EN ISO 13982 in case of dust).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1866
- Shipping Name
- RESIN SOLUTION
- Transport Class
- 3
- Packing Group
- III
Warning: Flammable liquids.
Warning: Flammable liquids.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for SR-Dur 2478 M?
The signal word is danger.
What is the physical form of SR-Dur 2478 M?
SR-Dur 2478 M is a liquid appearing as fluid with light yellow color. It has aromatic odor.
What is SR-Dur 2478 M used for?
Epoxy curing agent
What are the hazard statements for SR-Dur 2478 M?
This substance has 5 hazard statements:
- H226: Flammable liquid and vapour.
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H318: Causes serious eye damage.
- H332: Harmful if inhaled.