NextSDS Logo
Safety Data Sheet EN

BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A
Product Code
597188

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Phosphating Products for Metals

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 3
Skin Corr. Cat. 1C
Eye Dam. Cat. 1

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

Hazard Statements

H301 TOXIC IF SWALLOWED.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.

Precautionary Statements

P260 Do not breathe dust or fumes.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/ physician.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P330 Rinse mouth.
P361 If on skin (or hair): Take off immediately all contaminated clothing.
P363 Wash contaminated clothing before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
sodium fluoride 7681-49-4 30 - 60% Yes
Sulfamic acid 5329-14-6 5 - 10% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If symptoms are experienced, remove source of contamination or move victim to fresh air. If symptoms develop and persist, get medical attention. If breathing is difficult, give oxygen. Trained personnel should administer 2.5% calcium gluconate through a nebulizer for 20 minutes.

Skin contact

Remove contaminated clothing and footwear while rinsing the affected area with large amounts of running water for at least 15 minutes. GET IMMEDIATE MEDICAL ATTENTION. If iced solution of 0.13% aqueous Benzalkonium Chloride (Zephiran) or 2.5% calcium gluconate gel is available, rinsing may be limited to 5 minutes, with the soak solution or gel applied as soon as the rinsing is stopped. If using calcium gluconate gel, it should be continuously re-applied and massaged into the affected area until pain has been relieved for at least 30 minutes. If Benzalkonium Chloride (Zephiran) or calcium gluconate gel is not available, rinsing must continue until medical treatment is provided.

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.

Ingestion

Get medical attention. Do not induce vomiting. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

GET IMMEDIATE MEDICAL ATTENTION (Skin), Get immediate medical attention (Eye), Get medical attention (Ingestion).

Medical Treatment

Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.

Instructions

Wear self-contained breathing apparatus. Wear full protective clothing.

Firefighter Protection

Wear self-contained breathing apparatus. Wear full protective clothing.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Do not allow product to enter sewer or waterways.

Cleanup methods

Sweep up or gather material and place in appropriate container for disposal. Wash spill area thoroughly.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Provide adequate ventilation. Avoid breathing dust. Wash thoroughly after handling. Do not reuse the empty container.

Storage

Not available.

Hygiene

Wash thoroughly after handling.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Softening Point
---
Upper Explosive Limit
Not applicable
Evaporation Rate
Not available.
Colour
White
Odor Threshold
Not available.
Voc Content
Not applicable
Density
---
Physical State
Solid
Partition Coefficient
Not determined
Crystallisation Point
---
Colour Intensity
---
Appearance
---
Solubility In Fat
---
Kinematic Viscosity
---
Solubility In Water
Complete
Flammability
Not applicable
Vapor Pressure
Not determined
Form
---
Odor
Bland
Melting Point
Not determined
Molecular Weight
---
Relative Density
---
Decomposition Temperature
Not available.
Auto Ignition Temperature
Not determined
Boiling Point
Not determined
Solidification Point
---
Cloud Point
---
Dynamic Viscosity
---
Explosive Limits
---
Lower Explosive Limit
Not applicable
Solubility
---
Properties Status
---
Flash Point
Not determined
Vapor Density
Not determined
Relative Evaporation Rate
---
Freezing Point
---
State Under Standard Conditions
---
Physical State Data
solid
Bulk Density
---
Ph
4.0 - 4.8 (5% solution)
Metal Corrosion
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

Will not occur.

Avoid

Avoid dust formation.

Incompatible

This product may react with mineral acids and strong bases.

Decomposition

Upon decomposition, this product may yield sulfur dioxide, carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. May liberate hydrogen fluoride.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
2923
Shipping Name
Corrosive solids, toxic, n.o.s. (Sodium fluoride, Sulphamic acid)
Transport Class
8 (6.1)
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A?

The signal word is danger.

What is the physical form of BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A?

BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A is a solid with white color. It has bland odor.

What is BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A used for?

Phosphating Products for Metals

What are the hazard statements for BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A?

This substance has 2 hazard statements:

  • H301: TOXIC IF SWALLOWED.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.

What is the melting point of BONDERITE L-FM TI-KOTE A ACHESON CONVERSION COATING known as TI-KOTE A?

The melting point is Not determined and the boiling point is Not determined.