AICr

Move victim to fresh air. If symptoms persist, consult a doctor. If breathing is difficult, give oxygen, in the absence of breath use artificial respiration. Seek medical advice immediately.

Symptoms: Irritation of eyes, nose and throat. Metallic taste in the mouth, dryness and irritation of the throat, chills and fever.

In case of burns immediately cool the skin, apply dressing contact with doctor. In case of skin injury by sharp edges, clean, disinfect and dress the wound, if necessary, contact with doctor. In the case of persistent irritation consult a dermatologist.

Symptoms: Burns, skin injury by sharp edges.

Rinse eyes with running water with wide-open eyelids, a continuous stream of water for about 10 minutes. In the case of persistent irritation consult an ophthalmologist.

Symptoms: Irritation by fumes or dust.

Not applicable

Use powder extinguishing agents for metals. If they are not available, just use dry sand.

Do not use a direct stream of water – risk of explosion of steam, halogenated compounds

Thermal decomposition of the product may produce harmful smoke and gases. Avoid inhalation of combustion products, may pose a threat to health. Product in handling form is not flammable. Danger creates fine particles of product which may accumulate when working in dry conditions, or in the presence of oil mist. Dust the product are rapidly burning in fire. Form explosive mixtures in air. After igniting the material is virtually impossible to extinguish. Fire-fighting action should be limited to isolate the burning material, for example by covering with sand or cement and prevent the spread of fire. Melted product reacts violently with water, can cause an explosion.

Fire-fighting action should be limited to isolate the burning material, for example by covering with sand or cement and prevent the spread of fire.

In case of release of the product, move damaged packaging of the product into an empty container. Released product gather in closed container for disposal or reuse.

Do not allow to enter drains, groundwater, soil and open water courses.

Released product gather in closed container for disposal or reuse.

Avoid contact with eyes and skin, breathing dust of product created by cutting, sanding operation with product. Use personal protective equipment. Ensure adequate ventilation/exhaust in the workplace, prevent the formation of harmful concentrations of dust in the air, work in well ventilated areas. Observe good personal hygiene and wear protective clothing in accordance with information set out in section 8. Do not touch or move the castings of aluminium or hot materials before checking their temperature. Aluminium does not change colour when heated.

Store product in dry storage rooms. Keep away from sources of heat and fire.

Observe good personal hygiene and wear protective clothing. Ensure place for eyes and skin rinsing, provide easy access to running water, wash hands with soap and water before eating, smoking and after work, use general caution while working with chemical substances.

Store and use the product while ensuring adequate ventilation away from potential ignition sources like open fire.

Use engineering controls to reduce air contamination to permissible exposure level. Explosion-proof general and local exhaust ventilation. Monitor exposure and apply all possible technical measures to ensure the maintenance of the concentrations of hazardous products in the workplace below recommended exposure limits.

Recommended protective gloves. Standards: EN ISO 21420:2020, EN ISO 374-1:2017/A1:2018, EN ISO 374-2:2020, EN 16523-1:2015+A1:2018, EN 407:2020.

Safety glasses in a sealed cover (goggles) (e.g. EN 166). Standards: EN ISO 16321-1:2022, EN ISO 16321-3:2022, EN ISO 4007:2018.

Not necessary under normal conditions with sufficient ventilation, required during exposure to high concentrations of dust. Wear mask or respirator completed with the antidust filter. Standards: EN 140:1999/AC:2000, EN 143:2021, EN 149:2001+A1:2009.

Protective, working clothing. Body protection must be chosen depending on activity and possible exposure (according to EN ISO 13982 in case of dust). Standards: EN ISO 13688:2013, EN 14605:2005+A1:2009, EN ISO 20345:2022.

Do not allow to enter large amounts of product into ground water, sewage, waste water or soil.

Stable under normal conditions (see Section 7 – storage conditions)

Not applicable for product in handling form.

No data

In the case of dust creation avoid sources of ignition (dusts of aluminium alloys may form explosive mixtures with air). Aluminium castings must be stress-free against possible parting in order to prevent an explosion or a sudden cracking. During the melting of aluminium, aluminium alloy or aluminium scrap, eliminate the possibility of water intrusion. Water or moisture contact with hot or melted metal can cause a violent explosion. During the operation of heating and melting should be eliminated possibility of contact with strong oxidizing agents, to prevent the possibility of explosion.

Product may react with strong acids, alkalis and oxidizing agents to form hydrogen, which is flammable. Contact with chlorine-based solvents can lead to release of toxic and corrosive hydrogen chloride gas. Hot aluminium can react with solvent-based chlorine to form phosgene, a highly toxic and irritating gas.

Under normal conditions of use are not known

Dispose of waste in accordance with all Federal, State and Local regulations.

communicate with the manufacturer of the product on the possibility of processing waste. If it's not possible, deliver it to utilization in plants permitted to waste collection, transport, waste recovery and disposal. Do not empty into drains. Recovery or disposal of waste product should be made in accordance with applicable regulations.