Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ELATUR® CH
Regulatory Identifiers
- CAS Number
- 166412-78-8 Check regulations →
- EC Number
- 431-890-2 Check regulations →
- REACH No.
- 01-0000017810-74
Identified Uses
Plasticizer, Construction chemicals, Raw materials for coatings, Lubricant, Adhesives
Manufacturers & Suppliers
Will & Co. B.V.
manufacturer
Dellaertlaan 24, 1171 HG Badhoevedorp, Netherlands
+31 20 659 75 01
Emergency Contacts
The National Poisons Information Service, Birmingham
(+44) (0)121 507 4123
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Cyclohexane-1,2-dicarboxylic acid, diisononyl ester EC: 431-890-2 | 166412-78-8 | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Take affected persons into fresh air and keep quiet. Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Make sure to remove any contact lenses from the eyes before rinsing. Rinse opened eye for several minutes under running water. Seek medical treatment. Protect unharmed eye.
If affected person is conscious: Rinse mouth with water. Seek immediate medical advice.
Immediate Medical Attention
Seek immediate medical advice.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Water with full jet
Carbon monoxide (CO), Carbon dioxide (CO2).
Cool endangered receptacles with water spray.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with the eyes and skin. Wear protective equipment. Keep unprotected persons away. Ensure adequate ventilation
Do not allow product to reach sewage system or any water course.
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Pick up mechanically. Fill into labelled, sealable containers.
Materials: liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use personal protection equipment. Avoid contact with skin, eyes or clothing.
Store only in the original receptacle. Store in a cool location. Store under clean dry conditions. Keep container tightly sealed.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Chemicals-resistant protection gloves towards DIN EN 374. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: Nitrile rubber, NBR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Penetration time of glove material: The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
Use suitable respiratory protective device in case of insufficient ventilation. Filter A/P2
Protective work clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
Reacts with strong oxidizing agents.
To avoid thermal decomposition do not overheat. No further relevant information available.
Strong oxidizing agents
Carbon monoxide and carbon dioxide
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ELATUR® CH?
The signal word is no signal word.
What is the physical form of ELATUR® CH?
ELATUR® CH is a liquid appearing as colourless with colourless color. It has nearly odourless odor.
What is ELATUR® CH used for?
Plasticizer, Construction chemicals, Raw materials for coatings, Lubricant, Adhesives
What is the melting point of ELATUR® CH?
The melting point is Undetermined. and the boiling point is 394 °C.