NextSDS Logo
Safety Data Sheet EN

BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG
Product Code
379311

Regulatory Identifiers

CAS Number
N/A

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

http://www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 2
Skin Irrit. Cat. 2
Skin Sens. Cat. 1
Repr. Cat. 2
STOT SE Cat. 3
STOT RE Cat. 2
Asp. Tox. Cat. 1

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H225 HIGHLY FLAMMABLE LIQUID AND VAPOUR.
H304 MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
H315 CAUSES SKIN IRRITATION.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H336 MAY CAUSE DROWSINESS OR DIZZINESS.
H361 SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.
H373 MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat, sparks, open flames, hot surfaces - no smoking.
P233 Keep container tightly closed.
P240 Ground and bond container and receiving equipment.
P241 Use explosion-proof equipment.
P242 Use non-sparking tools.
P243 Take action to prevent static discharges.
P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P310 IF SWALLOWED: Immediately call a physician or poison control center.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P308 + P313 IF exposed or concerned: Get medical attention.
P331 Do NOT induce vomiting.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P370 + P378 In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P403 + P235 Store in a well-ventilated place. Keep cool.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Toluene 108-88-3 60 - 80% Yes
Talc 14807-96-6 5 - 10% Yes
Formaldehyde, polymer with p-tert-butylphenol and phenol 28453-20-5 0.1 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.

Skin contact

Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and shoes. Get medical attention. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Check for and remove any contact lenses. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Ingestion

If material is ingested, immediately contact a physician or poison control center. DO NOT induce vomiting unless directed to do so by medical personnel. If vomiting occurs, prevent aspiration by keeping the patient's head below the knees. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Get medical attention (for skin, eye, and ingestion exposure).

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use extinguishing measures appropriate to local circumstances and the surrounding environment. Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

Vapors may accumulate in low or confined areas, travel considerable distance to source of ignition, and flash back. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. Isolate area. Keep unnecessary personnel away. In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

isolate the hazard area and deny entry to unnecessary and unprotected personnel

Environmental

Prevent further leakage or spillage if safe to do so.

Cleanup methods

Transfer liquids to covered metal containers for recovery or disposal, or remove with inert absorbent.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Make sure containers are properly grounded before use or transfer of material. Keep container closed. Do not breathe gas/fumes/vapor/spray. Use only with adequate ventilation. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Do not taste or swallow. Do not handle or store near an open flame, heat or other sources of ignition. 'Empty' containers retain product residue (liquid and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition; they may explode.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Keep away from heat, spark and flame. Store in original container until ready to use.

Hygiene

Wash thoroughly after handling. Avoid contact with eyes, skin and clothing.

Fire prevention

Do not handle or store near an open flame, heat or other sources of ignition. Ground and bond metal containers for liquid transfer to avoid static sparks.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Solubility
Insoluble Water, Partially miscible Water
Crystallisation Point
---
Metal Corrosion
---
Auto Ignition Temperature
Not available.
Form
---
Vapor Density
---
Colour
Beige
Dynamic Viscosity
27.0 - 33.0 poise
Solubility In Fat
---
Softening Point
---
Ph
Not applicable, Product is non-soluble (in water).
State Under Standard Conditions
---
Flammability
Flammable liquid
Molecular Weight
---
Boiling Point
100 - 200 °C (212°F - 392°F) no method / method unknown Value of most critical component
Bulk Density
---
Evaporation Rate
Not available.
Solidification Point
---
Decomposition Temperature
> 300 °C
Upper Explosive Limit
7.1 %
Flash Point
4.0 °C (39.2 °F) None
Odor
no valuation
Cloud Point
---
Solubility In Water
Insoluble; Partially miscible
Relative Density
---
Kinematic Viscosity
2,700 - 3,300 mm2/s
Density
---
Appearance
---
Explosive Limits
---
Properties Status
---
Relative Evaporation Rate
---
Colour Intensity
---
Lower Explosive Limit
1.1 %
Partition Coefficient
Not available.
Voc Content
Not available.
Odor Threshold
not available.
Melting Point
Not applicable, Product is a liquid
Physical State
Viscous, Liquid
Physical State Data
liquid
Freezing Point
---
Vapor Pressure
132 mbar (50 °C (122°F)) no method / method unknown 29 hPa (20 °C (68°F))
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

This product may react with strong acids, bases and oxidizing agents.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Take measures to prevent the build-up of electrostatic charges.

Incompatible

Strong acids, alkalies and oxidizing agents.

Decomposition

Irritating and toxic gases or fumes may be released during a fire. Oxides of carbon.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1139
Shipping Name
Coating solution
Transport Class
3
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG?

The signal word is danger.

What is the physical form of BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG?

BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG is a viscous, liquid with beige color. It has no valuation odor.

What is the solubility of BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG?

Insoluble Water, Partially miscible Water

What are the hazard statements for BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG?

This substance has 7 hazard statements:

  • H225: HIGHLY FLAMMABLE LIQUID AND VAPOUR.
  • H304: MAY BE FATAL IF SWALLOWED AND ENTERS AIRWAYS.
  • H315: CAUSES SKIN IRRITATION.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H336: MAY CAUSE DROWSINESS OR DIZZINESS.
  • H361: SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.
  • H373: MAY CAUSE DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of BONDERITE S-MA 522 AERO C MASKANT known as TURCO FORM MASK 522 20KG?

The melting point is Not applicable, Product is a liquid and the boiling point is 100 - 200 °C (212°F - 392°F) no method / method unknown Value of most critical component.